MODEL 22610709 - 12 | PECO |
WARRANTY | PECO |
SAFETY | PECO |
WARNING! | WARNING! |
NEVER operate the mower unless the discharge | Do not work around the mower deck boot or the |
guard and either the deflector assembly or the | blower area until you are certain that the mower |
vacuum collector adapter are fastened securely in | blades and the blower fan have stopped rotating. |
place. |
WARNING! | WARNING! | |
To avoid serious injury, perform maintenance on | For your personal safety, ALWAYS mow UP and | |
the vacuum collector ONLY AFTER STOPPING THE | DOWN the face of slopes and NEVER across the | |
TRACTOR ENGINE AND WAITING FOR ALL MOV- | face. NEVER attempt to mow excessively steep | |
ING PARTS TO COME TO A COMPLETE STOP. Set | slopes and use caution when turning on any | |
the parking brake. Always remove the ignition key | slope. | |
before beginning the | ||
maintenance | ||
MODEL 22610709 - 12 TORO Z-MASTER | 2001 | PECO 3 |
ASSEMBLY | PECO |
into threaded holes to remove old blade. | B |
(This will push the impeller off the hub.) If the A | |
impeller is stuck on hit the base of the impeller | |
between each vein with a hammer then try the | |
bolts again. |
PARTS LIST | PECO |
REF. NO. | PART NO. | DESCRIPTION | QTY. | |
1 | ******* | BOOT PLATE (SPECIFY DECK SIZE) | 1 | |
2 | ******* | BOOT (SPECIFY DECK SIZE) | 1 | |
3 | J6006 | 7'- 8' HOSE CLAMPS | 2 | |
4 | ******* | 7' x 48' LOWER HOSE | 1 | |
5 | E6004 | 7' BLOWER CONE | 1 | |
6 | ******* | ENGINE/BLOWER/BLADE ASSEMBLY | 1 | |
E4052A | BLOWER HOUSING | |||
D4002 | 5HP BRIGGS & STRATTON ENGINE | |||
A0645 | 4 BLADE IMPELLAR W/ S4311 BUSHING | |||
W/ 3/4' SHAFT | ||||
D1016 | 6HP KOHLER ENGINE | |||
A0914 | 4 BLADE IMPELLAR W/ S4302 BUSHING | |||
W/ 1' SHAFT | ||||
7 | J6011 | 5'- 6' HOSE CLAMPS | 2 | |
8 | ******* | 6' x 36' LOWER HOSE | 1 | |
9 | V1054 | UPPER INLET | 1 | |
10 | A0023 | HARDTOP ASSEMBLY | 1 | |
11 | A0913 | BASE FRAME ASSY | 1 | |
12 | A0907 | (OPTIONAL) WEIGHT ASSEMBLY | 1 | |
13 | B2250 | CHANNEL CLAMP | 1 | |
14 | A0917 | MOUNT PLATE ASSEMBLY | 1 | |
16 | A0780 | ENGINE MOUNT ASSEMBLY | 1 | |
17 | B1941 | INSIDE INLET PLATE | 1 | |
18 | B1926 | OUTSIDE RETAINING PLATE | 1 | |
19 | J0316 | GAS STRUT | 2 | |
20 | A0021 | RIGHT HAND HINGE PLATE ASSEMBLY | 1 | |
21 | A0022 | LEFT HAND HINGE PLATE ASSEMBLY | 1 | |
22 | A0236 | LATCH ASSEMBLY | 2 | |
23 | A08221 | HARDWARE BAG | 1 | |
24 | VV2002 | PLASTIC CONTAINERS 7 CU. FT. | 1 |
EXPLODED VIEW | PECO |
ASSEMBLY | PECO |
ASSEMBLY | PECO |
SCHEDULED CARE | CARE REQUIRED |
Before Each Use | Check engine oil. |
Check all hose connections. | |
After Each Use | Clean Collector Box, hoses and engine of all grass and dirt. |
Every 10 Hours | Check that all screws, nuts, bolts, pins, etc. are present and |
secure. |
Dealer's City: ___________________________ | State: ______________ Zip: __________ |
PROBLEM | CAUSE | SOLUTION | |
Leaves and Grass | 1. | Engine speed too slow | A. Run at full throttle. |
not being picked | 2. | Ground speed too fast. | B. Use lower gear |
up completely. | 3. | Hose plugged. | C. Check and tighten all hoses. |
D. Unplug hose. | |||
Hoses plug easily. | 1. Grass or leaves too wet. | A. Wait for drier conditions. | |
2. Grass too high. | B. Reduce tractor ground speed/raise deck. | ||
3. | Container full. | C. Empty container | |
4. | Grass buildup in boot or | D. Clean thoroughly. | |
under mower deck. | |||
Vacuum Collector | 1. Buildup on blower blades. | A. Remove cone and clean blades. | |
blower vibrates | 2. | Bent or chipped blade. | B. Contact your dealer or PeCo. |
excessively. | |||
Unit fails to fill box. | 1. | Engine speed too slow. | A. Run at full throttle. |
2. | Buildup on inlet or screen | B. Clean thoroughly. | |
3. Grass is too wet or long. | C. Wait for dryer conditions. |